Draw tite activator 2 settings. Mounting, Bench test instructions, Wiring 2019-04-06

Draw tite activator 2 settings Rating: 7,7/10 807 reviews

Draw Tite Activator Wiring Diagram Gallery

draw tite activator 2 settings

The bulb should start to dim and get brighter and the dis- play should count up to 10 as the Manual Control is pushed. While still holding the brake pedal move the Sync Control slightly, the Display will change to the Sync setting. See vehicle's owners manual for special re-connection instructions. The display will change to the Sync mode. Electric trailer brake control for up to 4 braking axles. To determine the cold side probe the terminals of the switch with a test light until one is found that is only on when the brake pedal is depressed.

Next

Draw

draw tite activator 2 settings

The Sync Control adjusts trailer brake aggressiveness. Plug-N-Play feature allows quick and easy connection. The Sync adjustment has no effect on the manual control. The connector has two rows of wires, one row has four wires inside row the other has seven. A wiring diagram is a simplified conventional photographic depiction of an electrical circuit.

Next

Draw Tite Activator Wiring Diagram Gallery

draw tite activator 2 settings

Conventional Wiring Diagram Symbols If a line touching an additional line has a black dot, it implies the lines are linked. The display should count down to 0 and the bulb should dim and go off. Connect the white wire to the negative battery post with a ring terminal. A button will be a break in the line with a line at an angle to the cord, much like a light switch you could flip on as well as off. A schematic shows the plan as well as function for an electric circuit, however is not interested in the physical design of the wires. The Output setting is shown as 0 through 10 with 0 being the minimum and 10 the maximum.

Next

Draw

draw tite activator 2 settings

Defective Unit If the Brake Control unit does not function as described, return it for service or replacement. The Output setting is shown on the digital display when a trailer is connected and the brake pedal is pressed or the Manual Control is actuated. Adjust to 4 0 by sliding the Sync Control ahead or back as necessary. As the output changes the bulb should go bright and dim and the display should read 0 to 10. This indicates correct wiring and that the control is ready.


Next

Mounting, Bench test instructions, Wiring

draw tite activator 2 settings

The further to the left it is pushed the harder the brakes are applied until the maximum set by the Output Control is reached. B The unit must be easily reached by the driver. The majority of signs utilized on a wiring diagram look like abstract variations of the actual items they represent. For 1989-91 Ford E and F series trucks and vans with anti-lock brakes: Find the crescent shaped connector located on the steering column turn signal harness. If the stop seems slow and more aggressive braking is desired, move the Sync Control rearward while holding the brake pedal. Set the Output control to maximum + and set the Sync control to minimum -. The trailer brakes become more aggressive as the switch is moved toward the front of the tow vehicle.

Next

Draw

draw tite activator 2 settings

Slight adjustment of the Output Control may also be desirable. The Manual Control only applies the trailer brakes and would be used during initial setup and in situations where it is desirable to reduce speed slowly. It reveals the components of the circuit as streamlined forms, as well as the power and signal links in between the tools. The display should step up to 10 and the bulb should start out dim and slowly get brighter unhook and re-attach the red wire as many times as necessary to confirm this With the red wire still hooked up, slowly move the Output Control down to -. DescriptionThe Voyager® incorporates patented braking sensor by Tekonsha and is the best value you will find for smooth and secure trailer braking. Feed one black and one white, 10 Ga.

Next

Draw

draw tite activator 2 settings

A wiring diagram usually offers information about the family member setting and also setup of gadgets and also terminals on the devices, to aid in structure or servicing the gadget. Unlike a pictorial representation, a wiring diagram uses abstract or simplified shapes as well as lines to reveal components. They provide a smooth braking response in any stopping situation, with no need for adjustments. Assortment of draw tite activator wiring diagram. The Manual Control activates the tow vehicle and trailer stop- lights.


Next

Voyager Brake Control

draw tite activator 2 settings

Website Copyright © 2019 Horizon Global Corporation. The Sync setting is shown as 1 0 through 9 0 with 1 0 being the least aggressive and 9 0 being the most aggressive. They are additionally valuable for making repair work. The bulb should light brightly with no delay and the Display should read 10. Circuitry layouts demonstrate how the cords are attached and where they need to situated in the real device, in addition to the physical connections between all the components. Disconnect and reconnect the red wire.

Next

Draw Tite Activator Wiring Diagram Gallery

draw tite activator 2 settings

A wiring diagram is a simple visual depiction of the physical connections and also physical format of an electrical system or circuit. Advanced electronics minimize false braking for smoother ride. When and Exactly how to Utilize a Wiring Diagram Use electrical wiring representations to aid in structure or manufacturing the circuit or electronic device. A The unit must be mounted securely to a solid surface. It is used to setup and monitor the Brake Control and can be used when trouble shooting.

Next