Remington Premier Accutip Bonded Sabot Slug Designed for use in fully rifled shotgun barrels, Remington Premier Accutip Sabot Slugs are ideal for longer shots. Applying a small amount of stain to the barrel channel inletting may be helpful to your decision making process. When pushing the bolt forward, there is a different feeling than on the Model 700 or Model Seven. The magazine is sold out. You can view for all of our current loads in the ballistic chart section of our online catalog at These charts will help you to determine the range you will have for hunting specific game and the advantages that one load offers compared to another. Ammunition should be stored in the factory carton or package. We recommend starting at a range of 25-30 yards for initial sighting in.
When measuring barrel lengths, go from the gas port on the operating side of the receiver to the muzzle. You can find many of these cleaning products through your local dealer or through our online store at Another means of reducing lead fouling in rimfire guns is achieved by applying a very thin layer of copper or brass plating to the bullet. What is the manufacture date of Remington model 760 with serial number 7124726. Please have all available information on the firearm, including model, serial number, caliber, physical appearance, patent dates or numbers listed on the barrel, etc. Obviously, poor storage conditions, such as a humid or corrosive atmosphere, could cause product damage immediately. .
You most likely have the Remington Autoloading Shotgun, which was later re-named the Remington Model 11 in 1911. After production of the Remington 2020 Digital Optic Systems began, an issue with the programming in the charging cradle was found that would prevent the cradle from recognizing a deeply-discharged battery could be charged. The barrel, bolt, receiver and action bar have been enhanced. Pointed Soft Point Core-Lokt bullet, it delivers greater velocity, energy and bullet momentum at flatter trajectories out to 500 yards than any other 7mm Magnum. Ideal for close-in small game shooting, upland bird hunting such as quail, grouse and pheasant as well as hunting waterfowl close over decoys. If your firearm does have a serial number, if you will call or email us the serial number and model number we can determine the approximate age of your firearm. This thing has floated around the family for about 7 years.
I have, so I've been told, a Remington M11 12g, serial number 115xxx. Bob, do you have a link for that serial number place? For deer, antelope, sheep and goat size game we recommend 900 ft lbs minimum, 1200 ft lbs is adequate and 1500 ft lbs is preferred. If you still have concerns and wish to have the barrel guide stud reinstalled, please contact us at 800-243-9700 to obtain a Service Request Number. This is an old British measurement system. Enjoy your wood and steel antique! If it is deemed that your knife is not a manufacture defect you will be contacted before further steps are taken to repair your knife.
Before 1968 it was not mandatory for us to use serial numbers. If We guesstimate about 1000 produced each month that makes about 84 months between 1919 and when your's was produced or 7 years prior, or 1912. Try this link to enter your 2 or 3 letter code and find the year of manufa … cture. Previous to 2004, there was a front sight base held by two screws and the dovetail front sight tapped into the base. If a lubricant is desired, use dry graphite or similar non-congealing lubricant such as Rem Dri Lube. The locations of the barrel seal grooves in the magazine tubes are in slightly different places.
To order direct, call our Parts Department at 1-800-243-9700 or visit our online store at The exact barrel life of any given Remington barrel is almost impossible to predict. The bolt locks directly into the barrel, and the barrel is hydraulically pressed into the receiver. It is done by starting at the lower charge weight listed in the nominal range and increasing in 5 grain increments until an optimum load is achieved. Best of all its low cost allows for shooters, hunters and reloaders to enjoy their favorite shooting sports economically. The final choice should be governed by your taste. The one link that looked promising wouldn't work for me remingtonsociety. The 209-4 should not be used in gauges other than the.
For additional assistance you may wish to contact the following companies that specialize in older and obsolete ammunition. You can damage the threads if you shoot your firearm without a choke tube in the barrel. A two or three letter code on the left side of the barrel identifies the month and year of manufacture. There are a lot of memories in those shiney blue parts - I know, I still shoot my Dad's M31 pump, and my grandson is now starting with what is now his great-grandad's gun I too just inherited from my father his Remington Model 11 shotgun. In 1987, the new gas compensated Model 11-87 was introduced. He's used it every year for hunting so the blue has faded and the wood was refinished 30 years ago.
It was a 12 gauge autoloading lightweight, low-recoil shotgun and was voted 1997 Shotgun of the Year by Shooting Industry magazine. A general rule you can use follows. And as Alpo posted the link, that will tell you what the letter's meanings are. Your local hardware store may be a good place to look. If you contact us at 1-800-243-9700 or with the model of your firearm and 2-3 barrel code, we can determine the date of manufacture. In some cases, you will have to decide which meaning is correct based on other details.
The foundation of the Model 700 action is its unique bolt design. In 2002, it was brought back into production with a Rem Choke barrel. It was introduced in 12 gauge in 1905, 20 gauge in 1930 and 16 gauge in 1931 and was discontinued in 1947. This cleaning should involve removing the firing pin assembly from the bolt and cleaning each with a recommended powder solvent and lubricating oil. Additionally, this could result in premature wear on the receiver which would be a very expensive repair. The gallery stamp s signify function and accuracy testing.